Cutting Acrylic – 8 Guidelines To Get The Best Results

Acrylic is a great material to work with on your CNC system, as there is so much you can do with it, from lighted edge-lit signs to cool-looking inserts for speaker boxes, and other projects that need some “bling”.  However, there are some basic things you need to know in order to ensure success and five you a smooth finish when cutting Acrylic on your STEPCRAFT CNC system  Unlike wood, Acrylic will have a “sweet spot” in terms of speeds, feeds, and depth per pass that you want to be aware of.  Below are 5 important guidelines.

Stepcraft Cutting Acrylic

Guideline 1 – Secure Your Material

We can not stress enough how important it is to secure your Acrylic properly to your STEPCRAFT.  Failure to do so will result in excess vibration and flex which can ruin your cut or result in a very poor finish.  Whether you use the white stock table that comes with your STEPCRAFT or you have a T-Slot Table, you need to get a solid sacrificial board and attach it to the bed of the CNC.  We recommend using 3/4″ MDF board.  This material is very solid and flat.  If you are using T-Slot you can simply clamp the MDF to the table, but if you are using the White stock table then use several pieces of double-sided table to adhere the MDF to the white formica top.  We recommend using 2″ wide carpet tape and have had very good luck with this:XFasten Double Sided Carpet Tape, 2-Inch x 30 Yards

Once the MDF is secured to the table, use a couple pieces of double sided tape to secure the Acrylic to the MDF. Make sure you clean off the MDF to remove dust so the tape will adhere.  If you are using paperback Acrylic then you can use the double side carpet tape from above, but if you are taping directly to the acrylic, then you should use this type of tape as it will be easier to remove and will not leave residue: 3M Scotch Heavy Duty Mounting Tape, Clear (4010)

You might also want to clamp down the outside of the acrylic as well to ensure that the tape does not break loose. This will ensure that the Acrylic is fastened as solid as possible which will minimize any movement, flex or vibration.

 

Guideline 2 – Use The Right Bit

Amana 51410 O-Flute End Mill - Stepcraft CNC

You will never get the best results using wood bits to cut acrylic as cutting and chip removal is key. We recommend using a bit that is specifically designed for cutting acrylic. We found that we get the best results using an “O-Flute” end mill. If you read online, many posts will have you use the largest diameter end mill that you can.  While this might be true on an industrial-size CNC, on the STEPCRAFT, we have the best success with 1/8″ diameter “O-Flute” end mills.  The one we recommend the most is:Amana 51410 1/8″Dx1/8″SHK SPIRAL O PLASTIC

 

Guideline 3 – Set The Correct Feed Rate

Stepcraft Acrylic Feed Rate

We have found that the best feed rate for a STEPCRAFT 2 series CNC machine using a STEPCRAFT HF-500 Spindle is 30 mm/sec and using a KRESS 800W Spindle it is 38 mm/sec. A good rule of thumb would be to set the feed rate on the lower end and then you can always increase the speed using the F-SET  setting in UCCNC while the job is running.  If you determine that you are getting the best results with an F-SET of 120% then you can simply multiply the current feed rate x 120% and make that the new feed rate for that tool.  Then the next time you run a job, leave F-SET to 100%.

The idea is to get good clean chips from your cut without any melting of the plastic as its being cut.

 

Guideline 4 – Set The Correct RPM

Stepcraft Acrylic Spindle Speed

We have found that the optimal cutting RPM for acrylic with the recommended O-Flute bit above is 18,000 RPM. While you can use a faster RPM, you might have to increase your feed rate to prevent melting of the plastic.  Our tests have shown the above to give the best results, but there may be a slight deviation between different brands/types of acrylic.  Keep track of your settings and results so you can easily recall then for future job runs.

 

Guideline 5 – Set Your Pass Depth

Stepcraft Acrylic Pass Depth

Our normal guideline is 1/2 the diameter of the bit, which is a good starting point for many types of materials. However, a pass depth of .0625″ seems to provide the best results using the above bit and settings.

 

Guideline 6 – Set The Cut Direction To “Conventional”

Stepcraft Acrylic Feed Direction

Because of the direction that the cutter is rotating, we get the best results setting the cut direction, or the direction that the machine will move the cutter, to “Conventional”, or Clockwise.

Guideline 7 – Use The Ramp Feature

Stepcraft Acrylic Ramp Settings

Vectric programs all have the ability to set a ramp for each tool path. We recommend using a ramp when working with acrylic to allow the bit to enter the material at an angle as it lowers rather than plunging straight down. A smooth ramp of around 1-3 inches, depending on the size of the part, will give the best results.

 

Guideline 8 – Save Your Bit In The Tool Database

If using Vectric programs for your tool path creation, we recommend copying a 1/8″ end mill and renaming it “O-FLUTE FOR ACRYLIC” and then optimize your tool, settings for that tool. Now whenever you run acrylic again, you can simply reuse that tool and everything will be set for you.

 

VIDEO

By | 2017-05-27T15:18:44+00:00 August 23rd, 2016|Uncategorized|Comments Off on Cutting Acrylic – 8 Guidelines To Get The Best Results

About the Author: